Two quotes arrive for the same job: 5% openness, charcoal, 2,850 mm, 40 m rolls. The prices differ by four percent. One is cheaper, and on the basis of the paperwork there is no way to tell whether the four percent is a better deal or a smaller order.
A fabric quote is five decisions compressed into one number. When two quotes look identical, at least one of them has made a decision you were not shown. This article lists the five, in the order they change the price, and what to ask so the comparison is real.
Key takeaways
Colour count decides the order size before the panel count does. Our minimum is 1,000 m² per colour, so a four-colour project carries a 4,000 m² minimum.
Width sets roll length, and roll length sets the number of drops. 50 m rolls up to 2,500 mm, 40 m at 2,850 mm, 33 m at 3,200 mm.
Defect grading is a count, not an adjective. Three marked defects per 30 m is Grade A, four is B, five is C.
Packaging is part of the price. A roll without an outer tube is cheaper per square metre and more expensive per delivered roll.
Lead time means nothing without a starting point. 20–25 days from deposit and 20–25 days from enquiry are different promises.
Line one: colour, and whether it exists in your width
The colour reference is the first thing that changes a quote, because it decides which series a project can use.
The two constructions share yarn, weave, weight and thickness. They differ in openness and in colour count:
Property | 3% series → 5% series |
Openness | 3% → 5% |
Colours | 17 → 4 |
Weight | 544 g/m² ±10, both series |
Thickness | 0.73 mm, both series |
Yarn | 165 tex, both series |
Weave density | 45.5 × 35.5 yarns/inch, both series |
If a project starts from a colour, the openness is not a free choice. A colour held only in the 3% series makes the 5% series an unavailable option, whatever the project wanted.
All five of our widths can be produced in every colour of both series. That is worth confirming rather than assuming, because in many ranges the widest width is held in only a handful of colours — and a buyer who specifies width first discovers the colour gap second.
Ask: which widths do you hold in this exact colour reference?
Line two: minimum order, and its unit
The minimum is 1,000 m² per colour. Two words in that sentence change the arithmetic.
It is square metres, not metres. At 3,200 mm, 1,000 m² is about 312 m of fabric. At 1,600 mm it is about 625 m — the same minimum is twice as long on the narrow roll.
And it is per colour, not per order. A four-colour project does not have a 1,000 m² minimum; it has a 4,000 m² minimum.
Colour count | Total minimum |
1 | 1,000 m² |
2 | 2,000 m² |
3 | 3,000 m² |
4 | 4,000 m² |
That is the line where two quotes diverge most often and least visibly. A quote that looks cheaper per square metre may simply assume one colour.
Ask: is this price based on one colour or four, and what is the minimum in square metres per colour?
Line three: width, roll length and the cutting plan
Width is the second-largest cost lever and the one most often fixed by accident. The published widths are 1,600, 1,900, 2,500, 2,850 and 3,200 mm. Roll length falls as width rises: 50 m up to 2,500 mm, 40 m at 2,850 mm, 33 m at 3,200 mm.
That matters because a wider roll is heavier, not longer. A fabricator cutting 2.60 m drops gets 19 pieces from a 50 m roll and 12 from a 33 m roll, even though the 3,200 mm roll contains more square metres.
A quote that names only a width, without the roll length that comes with it, is not yet a quote.
Ask: what roll length comes with this width, and how many drops does that give at my drop length?
Line four: the defect grade, and who carries the offcut
Defects are marked in red during production, at the point they are found, then counted per 30 m:
Grade | Marked defects per 30 m |
A | 3 or fewer |
B | 4 |
C | 5 |
Where defects cluster inside one metre, the section is normally cut out rather than left in the roll, which changes the delivered length. A length that is marginally short of nominal is usually this, not a short shipment.
Two quotes can both say "first quality" and mean different counts. The grade is the only version that can be checked on arrival, by unrolling the roll and counting the same red marks the inspector counted.
Ask: what defect grade, and what count, is this price quoted against?
Line five: packing, which is never free
The roll build is eight layers, and two of them are structural rather than protective:
Layer | What it does |
Inner paper tube, 76 mm bore, 6 mm wall | Keeps the roll cylindrical and fixes the start of the wind |
EPE foam over the tube | Removes the hard-core impression that becomes a permanent pressure mark |
Defect marking | Locates defects so downstream cutting can avoid them |
Machine tightening | Removes internal air gaps so layers cannot rub against each other |
Stretch film | Dust and moisture barrier; holds the roll from loosening |
Outer plastic sheeting | Second barrier; carries the label |
Outer paper tube, 240 mm bore, 5 mm wall | Takes stacking and impact load that would otherwise reach the fabric |
Hollow end caps, about 0.2 kg | Handling grip, end-face protection, axial location |
A supplier who omits the outer tube has removed a layer that costs a few percent of the fabric value and prevents the most visible class of transit damage. The saving is real; so is the risk. On arrival the check is a tape measure: 76 mm bore inside, 240 mm outside.
Ask: what is the roll build, tube inside and outside, and is the roll labelled for traceability?
The line that is not on the quote: lead time
Lead time appears on the order confirmation, not the quote, and it is the line most often quoted without a starting point.
Ours is 20–25 days from the confirmed order and the deposit. A quote measured from the enquiry date and a quote measured from the deposit are not the same promise, and only the second can be kept by a production plan. When a mill holds an allocation queue, the production window can be short while the queue is long — which is why the two numbers are not comparable unless both clocks start in the same place.
Ask: does the clock start at enquiry or at deposit?
What the five lines add up to
A comparable quote names the colour reference, the colour count, the width with its roll length, the defect grade and count, the roll build, and the point where lead time starts. With those six, two prices can be compared. Without them, the cheaper quote is a smaller order with a shorter roll and no outer tube.
None of that requires trusting the supplier. It requires the supplier to write down decisions that were already made.
What we publish, and what we do not
For clarity, since it comes up: we do not publish a price per square metre on this page, because the number depends on colour count, width, roll length and quantity together. We do not state a warranty period. And we do not make UV-protection claims for the fabric — UV performance depends on the finished construction and would need to be tested for the specific fabric and colour.
Those three are left out deliberately rather than estimated, because a number on a website becomes a commitment a specific order has to meet.
The three questions worth sending first
Colour reference and colour count. Not a colour name — a four-digit code, and how many colours the project really needs.
Width with its roll length. The two are one decision, and the roll length is what the cutting plan uses.
Defect grade and count. An adjective cannot be verified; a count can.
Shandong Orenda New Materials Co., Ltd. manufactures PVC-coated fibreglass sunscreen fabric for exterior roller blinds and zip-screen systems. The range is woven in five widths, coated in-house, and supplied in 3% and 5% openness.