Storing Fabric Rolls Between Projects: What Actually Damages Them

Created on 11.14
A roll leaves the factory round, tight and wrapped. Three months later it is opened for a job and the first two metres will not hang flat. Sometimes the fault was there at dispatch. Often it was not: it happened in a warehouse, on a shelf, under another roll, or on the floor of a van.
Storage damage is easy to produce and hard to argue about afterwards, because it looks like a manufacturing defect. This article sets out what the packaging is designed to prevent, which storage habits defeat it, and how to tell a storage mark from a supply fault before the fabric reaches the cutting table.

Key takeaways

  • The outer tube carries the load, not the fabric.
  • A roll should lie flat and be supported along its length.
  • The end cap is a handle, not a foot.
  • The stretch film is the moisture and dust barrier.
  • Storage marks are local and repeat at contact points.
0
Photo: three rolls side by side. Where one roll rests on another, the outer tube deforms along a single contact line.

What the packaging is protecting, layer by layer

Our rolls ship in eight layers, and each one exists to stop a specific failure. Read as a list of things that can still go wrong in storage:
Layer
What it is there to stop
Inner paper tube, 76 mm bore, 6 mm wall
The roll collapsing inward and creasing at the core
EPE foam over the inner tube
The hard tube printing a permanent mark into the innermost wraps
Red defect marks through the roll
A marked defect being cut into a finished panel
Machine tightening
Loose wraps that shift and rub against each other in transit
Stretch film
Dust, moisture and the roll unwinding in the container
Outer plastic sheet
A second seal, and protection of the film itself
Outer paper tube, 240 mm bore, 5 mm wall
Point loads, impact at the ends and rolling in transit
Hollow end caps, about 0.2 kg each
Axial movement, and a grip point for lifting
Every one of those layers assumes the roll stays horizontal and the load stays spread along the tube. Storage that breaks either assumption defeats the packaging without visibly damaging it.

The three ways a stored roll gets damaged

A flat spot from a point load. The outer tube is rigid in the direction of its length and much less so across it. Rest a roll on a narrow bar, or stack another roll across it, and the tube ovalises slightly at that line. The fabric underneath takes the same shape and keeps it, because the coating is thermoplastic and the deformation is held for weeks rather than minutes.
A scuff ring from axial movement. If a roll is stored at an angle, or lifted without the end caps, the roll body can slide along its tube. The end face then rubs against whatever it is resting on. The result is a ring of fine abrasion or a crease near one end, and it looks nothing like a weaving fault.
Dust and moisture after the film is cut. The stretch film and outer sheet are the only barrier between the coated surface and the air. Once a roll is opened for a part order, the remainder is exposed. In a workshop that is usually harmless for a few days and progressively less harmless over a season.
0
Photo: rolls seen end-on. Full-length support keeps this circle round; a narrow support flattens it at the contact line.

Stacking: what carries the load

The question is not how many rolls high, it is where the weight goes.
A roll lying on a flat shelf, a pallet or a rack with rails running the full length is supported continuously. A roll lying across two rails set close to its ends is supported almost as well, because the bending moment is small. A roll lying across two rails set near its middle — or across another roll — has its whole mass hanging on a short span, and that is where flat spots come from.
Arrangement
What happens to the roll
Full-length flat support
Load spread along the tube; no bending
Rails near both ends
Small bending moment; acceptable
Rails near the middle
Tube bows; flat spot under each rail
Roll resting across another roll
Line contact at one point; flat spot and possible scuff
Roll on the floor, no support
Contact along one line; dust and moisture at that line
Two practical consequences. First, mixed widths should not be stacked so that a narrow roll bridges two wider ones. Second, a roll should not be left bridging a gap for weeks "temporarily", because the set it takes is a function of time as much as load.

Standing a roll on its end

Standing a roll vertically looks tidy and saves floor space, and it is the fastest way to damage an end.
The end cap is a hollow plastic disc of about 0.2 kg. Its openings are there so a person can grip and lift the roll. It is not designed to carry the roll's weight, and it cannot: a 2,850 mm roll of 40 m fabric is about 62 kg of fabric plus about 12 kg of tube, film and caps, bearing on a ring of coated fabric a few millimetres wide.
Standing also removes the outer tube's contribution, because the tube protects against loads applied across its length, not against loads applied along its axis.
Format
Typical packed weight
1,600 mm × 50 m
about 55–57 kg
1,900 mm × 50 m
about 63–65 kg
2,500 mm × 50 m
about 79–81 kg
2,850 mm × 40 m
about 73–75 kg
3,200 mm × 33 m
about 68–70 kg
Weights are fabric at 544 g/m² plus the tube, film and cap set, which adds roughly 11–13 kg on these formats.
If floor space forces a vertical store, the roll needs a cradle that takes the load on the tube wall rather than on the end face. That is a racking decision, not something the packing can solve.

Once the film is open

A part-used roll is the one most likely to be damaged, because it has lost its seal and is handled more often.
Three habits cover most of the risk. Keep the roll horizontal on a full-length support rather than leaning it against a wall. Rewrap the open end with the original film or a fresh stretch film, so dust does not settle into the weave and moisture does not sit on the coating. And write the opening date on the wrap, so the oldest open roll is used first.
The inner EPE foam should stay in place until the roll is mounted on the machine. It is doing the same job in the warehouse that it did in the container.

What we can and cannot tell you about storage conditions

Our packing document specifies how a roll is built and what each layer protects. It does not specify a warehouse climate, and we do not publish a storage temperature or humidity range, because we have not measured one and a number invented for a web page is worse than no number.
What we can say is what the construction implies. The coating is thermoplastic, so sustained heat and sustained pressure act together: a roll pressed against a warm surface for a season will take a set that the same roll would not take in a cool, evenly supported store. That is a statement about mechanism, not a specification.
If a project requires a formal storage condition for an audit or a warranty file, ask us and we will answer for the specific construction rather than publish a general figure.

How to tell storage damage from a supply defect

The distinction matters because the remedy is different: a supply fault is our problem, a storage mark is not, and both look similar on a bench.
What you see
What usually produced it
Flat spot at a repeating distance from one end
Rack rail or another roll resting at that point
Ring of abrasion near an end face
Axial sliding, usually from lifting without end caps
Crease running along one edge
Tension difference at coating, or a roll stored leaning
Band straight across the full width
A machine stop during production
Crease concentrated near the core
Winding tension, visible when the first metres are unwrapped
Dust or a dull patch on the outer wrap only
Film opened in storage; surface contamination
Two tests settle most cases. Unroll about three metres from each end and look at the fabric, not the wrap. Then check whether the mark is local, meaning one point, or continuous, meaning a line across the width. Local marks at contact points are storage. Continuous lines are process.

A storage check you can run in ten minutes

Do this when a delivery arrives and again before a roll goes to the cutting table.
Check
What you are looking for
Roll is round, not ovalised
Sight along the tube from one end
Outer tube unbroken at both ends
Cracks or crush marks at the rim
End caps present and seated
Missing caps mean the roll has been lifted bare
Film continuous, no splits
Any opening is where moisture enters
No line contact from stacking
Look along the top of the roll for a flat band
Label and defect marks legible
You need them to plan the cut
Ten minutes at goods-in is cheaper than discovering a flat spot after the panel is cut, and it is the only point where you can still prove where the damage happened.

Where this comes from

The layer structure, tube dimensions, cap weight and tightening practice are from our own packing specification, the same document that governs what leaves the factory. The weights are calculated from 544 g/m², the published figure for both the 3% and 5% series, multiplied by the roll area; packing weights are from the tube and film specification. The failure descriptions are from what we see in claims and in customer stores, not from a laboratory study, and we have said so rather than dressing them as test results.
If a roll arrives with a mark you cannot classify, send a photograph of the mark, the roll end and the outer tube together, and we will tell you which of the patterns above it matches.
Contact
Leave your information and we will contact you.

Factory Address

Building 2, Jiangbei Optical Fiber Industrial Park, West of Hesheng Road, North of Yonghe Road,

Xintai Development Zone, Tai'an, Shandong 271208, China

Contact Us

Email:taylor@orendablinds.com
Tel:0086 18553863016

电话