From enquiry to container: how a first fabric order actually runs

Created on 11.13
Most first enquiries arrive as one line: "Please send your best price for sunscreen fabric." That line cannot be answered accurately, and both sides spend a week discovering why.
A fabric order has a fixed sequence of decisions. Each one narrows the next, and the ones that get skipped are the ones that come back later as a change order, a substitute colour, or a roll that does not match the cutting plan. This article sets out the whole sequence — what to send, what comes back, and what happens at each stage — so a first order can be placed in one pass.

Four numbers open an enquiry

An enquiry that can be quoted immediately contains four things:
What to send
Why it decides the order
Colour reference
A four-digit code, not a name. The colour decides which series is available
Series, 3% or 5%
The two weaves carry different colour ranges
Width, with the panel size it serves
The width has to clear the widest drop plus edge allowance
Roll length, or "standard is fine"
Roll length follows width, and it decides drops per roll
Everything else — packing, loading, delivery — follows from those four. An enquiry without them can still be answered, but the answer will be a range rather than a quote.
The most common omission is the panel size. A buyer states the fabric width they want, but not the blind it is for. Without the panel size the width cannot be checked against the cut, and the recommendation becomes a preference rather than a calculation.

Samples: what is free and what is not

Two kinds of sample serve two different questions.
A4 swatch cards answer "what does this colour look like". They are free, and they cover the colour list. They do not answer "how does this weave behave in a panel", because a flat card does not show light transmission at scale.
Roll samples answer the second question. They are cut from production and sent against freight cost. They are worth requesting when a colour is being approved by a client, or when two openness factors are being compared on site.
A practical note on the swatch card: it is the wrong instrument for judging light level. A 50 mm swatch held against a window shows colour. It does not show what a 2.4 m panel does in a room. That judgement needs a roll sample in the actual opening — or a measured transmittance figure, if one exists for that colour.

What the quote contains

Three commercial terms come with a quote, and each one has a qualifier that matters as much as the number.
Minimum order: 1,000 m² per colour. It is square metres, not metres. And it is per colour, not per order — a four-colour project carries a 4,000 m² minimum. That distinction decides whether a multi-colour specification is viable, and it is better checked before samples are approved.
The width then changes what the minimum means in rolls. At 3,200 mm, 1,000 m² is about 312 m of fabric. At 1,600 mm it is about 625 m. The same minimum is twice as long on the narrow roll, which changes the core count, the handling and the freight.
Lead time: 20–25 days from the confirmed order and the deposit. The starting point matters. A quote measured from the enquiry date and a quote measured from the deposit are not the same promise, and only the second one can be kept by a production plan.
That is the distinction worth pressing on any supplier: ask what the clock starts from. Two mills quoting 20 and 25 days are not comparable if one counts from enquiry and the other from deposit.

Production, and the grading that runs alongside it

Once the order is confirmed, the fabric is woven and coated as a continuous run, then wound, graded and packed.
Defects found during production are marked in red at the point they are found, for three reasons: they cannot be missed later, downstream cutting can avoid them, and the count becomes data instead of a memory. The roll is then graded by defect count per 30 m:
Grade
Marked defects per 30 m
A
3 or fewer
B
4
C
5
The grade is the difference between a claim that can be checked and one that cannot. A roll arrives with a label, a batch reference and a defect count. If something is wrong, the label is what makes the roll traceable to a coating run and an inspection record — which is why the label, not the damage, is the first thing to photograph.
Where defects cluster inside one metre, the normal practice is to cut that section out rather than leave it in the roll. That changes the delivered length slightly, and it is worth knowing in advance so a length that is marginally short of nominal is not read as a short shipment.

Packing: eight layers, two of them structural

The pack is built from the core outwards, and the two tubes do different jobs.
Layer
What it does
Inner paper tube, 76 mm bore, 6 mm wall
Keeps the roll cylindrical; fixes the start of the wind so it cannot slip
EPE foam over the tube
Removes the hard-core impression that becomes a permanent pressure mark on the innermost layer
Defect marking
Locates defects so downstream cutting can avoid them
Machine tightening
Removes internal air gaps so the layers cannot rub against each other in transit
Stretch film
Dust and moisture barrier; holds the roll from loosening
Outer plastic sheeting
Second barrier; protects the film and carries the label
Outer paper tube, 240 mm bore, 5 mm wall
Takes stacking and impact load that would otherwise reach the fabric
Hollow end caps, about 0.2 kg each
Handling grip, end-face protection, and axial location
Two details carry most of the protection. The foam layer goes on before the fabric, so the first turn never touches paper — the innermost layer has the smallest radius and takes the highest pressure per unit area, which is exactly where compression damage concentrates. And the outer tube is what makes the load path run through packaging rather than through the fabric.
The part worth checking on arrival is the two dimensions: 76 mm core inside, 240 mm outside. Those two numbers tell you whether the pack was designed around a load path or around a habit, and they can be verified with a tape measure before anything is unwrapped.

Loading: the container fills by volume, not weight

Container
Approximate fabric load
20 ft
about 22,000 m²
40 ft
about 35,000 m²
At 544 g/m² those loads are about 12 and 19 tonnes, well inside a 20-foot container's payload. The constraint is the 240 mm envelope of each roll and how efficiently cylinders stack, not the weight.
Two consequences follow. A container of narrow rolls carries less area per cubic metre than one of wide rolls, because more of the volume is tube. And the loading figure is an estimate that assumes a normal width and roll-length mix — a project with one unusual roll length will not hit it.

The ten-minute check on arrival

Before signing off a delivery, five things are worth doing, and they need a bench, a light source and a tape measure.
Open the first three metres and the last three metres. Start and stop effects live at the ends of a roll, so checking there first keeps them out of a claim about the whole roll.
Measure the core and the outer tube. 76 mm inside, 240 mm outside.
Photograph the label before unwrapping. Traceability starts there.
Look at the end faces. End damage is visible without unwinding, and it predicts where creases will be.
Count the marked defects against the length. The grade is a count, and it can be verified independently.
Ten minutes of that produces a description a supplier can act on. "Three bands, irregular, in the first two metres, plus one crease near the core" is a technical claim. "The fabric is bad" is not, and it usually gets answered with a replacement roll rather than a fix.

What to expect at each stage

Stage
What happens, and what you receive
Enquiry
Four numbers reviewed against the colour and width lists; confirmation that the combination exists, or a no
Sampling
Swatch card and, if needed, a roll sample; a physical colour reference
Quote
Minimum, lead time and terms, with their qualifiers stated
Order
Deposit received and run scheduled; order confirmation with the date the clock started
Production
Weaving, coating, winding and defect marking; roll labels with grade and batch
Packing
Eight-layer build; roll ready to load
Loading
Container filled by volume; loading figures
Arrival
Ten-minute check; a traceable basis for any claim
The value of writing the sequence down is that it makes the gaps visible. Most of what goes wrong in a first order is not a defect in the fabric; it is a decision that was skipped at one of these stages and discovered at a later one.

A note on what we do not publish

For clarity, since it comes up in almost every enquiry: we do not publish a price per square metre on this site, because the number depends on colour count, width, roll length and quantity together. We do not state a warranty period. And we do not make UV-protection claims for the fabric — UV performance depends on the finished construction and would need to be tested for the specific fabric and colour.
Those three are deliberately left out rather than estimated, because a number on a website becomes a commitment that a specific order has to meet.
Shandong Orenda New Materials Co., Ltd. manufactures PVC-coated fibreglass sunscreen fabric for exterior roller blinds and zip-screen systems. Questions about a first order: see the contact page.
Contact
Leave your information and we will contact you.

Factory Address

Building 2, Jiangbei Optical Fiber Industrial Park, West of Hesheng Road, North of Yonghe Road,

Xintai Development Zone, Tai'an, Shandong 271208, China

Contact Us

Email:taylor@orendablinds.com
Tel:0086 18553863016

电话